By installing LED tube lights, you may save money on utility bills and get potentially risky fluorescent lights out of your home or office. However, most LED light tubes available nowadays can not be directly installed in an existing fluorescent fixture. You will have to make certain basic modifications to the fixture in order to correctly install the bulbs.

This particular Philips Ambient LED 7-Watt Medium Base R20 Indoor Flood is a lamp fixture that emits a white light free from any bluish tint. It is soft and cool on the eyes. If you are one person who wish to have recessed lighting then these LED lamps are the perfect solution.

Installing an LED tube light in a pre-existing fluorescent fixture is very simple. In addition, you should be able to purchase fixtures especially designed for LED light tubes in the near future, and they should actually be cheaper than the equivalent fluorescent fittings. This article will provide a brief overview explaining what you should know in order to set up the new energy-saving fluorescent tube lights in an existing tube lighting fixture.

Fluorescent fixtures are designed to support a specific types and size of fluorescent tube. A fluorescent tube is integrated into a fluorescent lighting system which contains two or three main components:

(1) the fluorescent lamp (fluorescent bulb or tube)

(2) the ballast, and then

(3) the starter system.

In addition, the system for a tube light includes a lamp holder and a switch. Depending on the particular fluorescent lighting system, the starter may be a replaceable component, a starter may not be required, or the starter function may be incorporated into the ballast. The starting function may also rely on the physical design of the fixture. To retrofit a tube light holder to support an LED tube lights, the ballast (and starter if a separate one is present) must be disconnected.

A few simple tools are needed, including a wire cutter and wire stripper (frequently incorporated into the same tool), a set of pliers, a screwdriver, and some wire nuts for reconnecting the wires once you have removed the ballast.

Once the old lamps are removed from the lamp holders and the electrical power to the fixture is turned off, you will possibly have to remove the reflector that is located behind the bulbs and provides a housing for the wiring and ballast that lie behind it. Usually, it is quite easy to remove the reflector or cover, but if it is not clear how to do this, you should consult the documentation from the fixture company.

If the fixture contains an electronic ballast, you only need to remove that and then wire the power directly to the lamp holders, completing one circuit for each bulb. This is quite simple, and typically you may use the existing wire in the fixture and then simply add some wire nuts. If you have an older fixture with a magnetic ballast and starter, you will have to remove or open the starter and take out or short the magnetic ballast.

When the ballast have been removed and the wires reconnected to complete a circuit for each bulb, replace the reflector or cover over the wiring and the area where the ballast was located, and the LED tube lamps may be inserted in the end sockets. Unlike fluorescent lights which do not have a top or bottom, an LED tube light will have an obvious top and bottom, with metallic heatsink situated on the backside of the tube and the LEDs noticeable under a lens on the side that will be aimed towards the area to be illuminated. Place the cover back on the fixture (if there was one) and turn on the electricity. Turn on the switch and if you have done everything appropriately, you should have as good or better light using approximately half the electricity and lasting as long as 50,000 hours or more.

Why Exactly The Prices For Investing In LED PL Downlights Is Really High
You might be put off investing in LED PL downlights since they are so expensive. Nonetheless what you should remember is that once set up such lighting can save you a great deal of money each year.

All These Advantages Must Be Taken Into Consideration And They Certainly Seem To Favor Choosing An LED Light Manufacturer
If you are searching for a dependable LED flood light manufacturer, it can be an extremely tiresome job sometimes, especially if you don't really know what to search for. Extensive research needs to be done, therefore, if you like to get the best results.

What Type Of Lights Should You Choose- LED Or CFL?
Recent news indicates that the world is really having problems with electricity supply. Power shortage has taken scientists to make radical measures to be able to fix this problem.

Why LED Flood Lights Needs To Be Set Up As A Security Measure At Your House
It isn't just entrepreneurs but also homeowners with large properties will find setting up of LED flood lighting a great idea. Even when used continuously you will find that these flood lighting will last considerably longer before the lights within them fail to work and have to be replaced.

LED Flood Lights For Your Lighting Choice
LED Floodlights are at present very popular for being an extremely competent, long lasting, and cheap lighting option. These lights are capable of fulfilling your indoor and outdoor lighting needs.

Energy Efficient LED Tube Lights
There are plenty of common service fluorescent tube lights in the market place today, until lately these were regarded the most energy efficient lighting solution available.

Very Small Halogen Spot Lamps Normally Are Used To Give More Focused Beam Or Accent Lighting
Very small halogen spot lamps are usually used to give more focused beam or accent lamps. They really are broadly used as a more energy saving option to incandescent bulbs in retail stores and home lighting applications.

Associated Articles

Associated Resources